ZhonghengbiaoZHB
Robot parts and independent repair support. From Foshan, China, to your next inquiry. Talk to us ›
Robot Repair & Maintenance

ABB Robot Maintenance for Grounding and Bonding Inspection

ABB robot maintenance should include documented grounding and bonding checks to help isolate power, cable, and controller-related faults.

ABB Robot Maintenance for Grounding and Bonding Inspection
In this article

ABB robot maintenance should include grounding and bonding inspection when unexplained controller faults, communication interruptions, intermittent servo conditions, or cabinet electrical concerns occur. Record the complete alarm text, robot and controller identifiers, fault time, operating condition, and recent work before diagnosis. A grounding concern can involve the installation, controller cabinet, manipulator, cables, or connected equipment, but the symptom alone does not prove that any one component is damaged. Inspection must follow the applicable ABB documentation and the site electrical safety procedure. ABB Robot Maintenance Scope and Limits This guidance applies to ABB industrial robot systems where the robot, controller, associated cabling, and connected cell equipment require maintenance review after electrical work, relocation, cabinet service, recurring unexplained faults, or changes to connected equipment. It does not identify a specific ABB controller, robot model, alarm code, cable assembly, or terminal arrangement. Grounding and bonding requirements vary by controller generation, robot model, installation design, local electrical rules, and connected peripheral equipment. Use the documentation that matches the installed ABB system before accessing or altering any electrical connection. Information to Record First Create a compact fault record before resetting alarms or changing parts. Complete alarm code and full text: record the message exactly as displayed. Date and exact time: record when the event first occurred and when it was last observed. Faulted axis: identify the axis only when the alarm or diagnostic record identifies one. Robot position/posture: document the position when the event occurred. Program step or motion: record the active task, command, or operating state. Actual speed and load condition: note the programmed or observed condition without estimating values. Reset result: state whether the fault cleared, remained active, or returned. Time until recurrence: record the elapsed operating time only when known. Related power, communication or feedback alarms: preserve earlier and associated messages, not only the final alarm. Safety and Preparation Isolate the equipment using the approved site procedure before cabinet or connection inspection. Only personnel qualified for the equipment and local electrical work should inspect protective-earth, bonding, or power-related connections. Confirm that drawings, controller documentation, and maintenance records match the installed robot and cell. Do not use a generic terminal location, conductor size, measurement value, or test method from another ABB model as evidence for the current system. Diagnostic Sequence Start with the information surrounding the fault. Review whether maintenance, relocation, cable routing changes, welding-system work, peripheral installation, or control-cabinet modifications occurred before the first event. This input helps determine whether the next inspection should focus on a changed part of the installation rather than assuming a robot component has failed. Inspect accessible external conditions for physical damage, loose mounting hardware, damaged cable protection, moisture, contamination, corrosion, or signs of overheating. The inspection target is the visible installation condition around the controller, robot base, cable routes, and connected cell equipment. If damage or contamination is observed, record its location and relationship to the affected circuit or cable, then follow the applicable service procedure. Visible condition alone cannot establish electrical continuity, component health, or the root cause of an alarm. Review the approved installation documentation for the intended protective-earth and bonding arrangement. Compare the documented arrangement with the installed controller, robot, and connected equipment. A mismatch, undocumented modification, or uncertain connection requires verification by qualified personnel against the matching ABB documentation and site electrical design. Do not alter grounding paths, shielding terminations, or protective devices based only on a general troubleshooting article. Next, review alarm history and operating conditions. Earlier power, communication, safety, drive, or feedback-related alarms may provide a more direct diagnostic branch than a later general fault. If an earlier alarm identifies a particular axis, cable path, drive-related condition, or external interface, inspect that branch according to the correct ABB service information. Do not attribute a feedback-related or motor-related fault to grounding without supporting alarm history, inspection evidence, and model-specific checks. How to Distinguish Similar Causes A grounding or bonding concern may be considered when records show an installation change, a damaged connection, an undocumented cell modification, or a fault pattern associated with an external condition. It remains only one possible branch. Repeated faults can also arise from external power conditions, damaged cables, controller hardware, drive-related equipment, safety circuits, communication interfaces, incorrect configuration, or an associated mechanical issue. The complete alarm history, exact equipment identification, and approved manufacturer procedures determine which branch should be evaluated first. When Repair or Replacement May Be Considered Consider professional inspection or repair when qualified review identifies damaged wiring, a compromised connection, contamination, overheating evidence, or an unresolved recurring fault after the installation and alarm history have been assessed. Any replacement part must match the exact ABB robot or controller model, part number, hardware revision, and connector layout. Do not replace a controller, cable, servo motor, or feedback-related component merely because the robot has an intermittent fault. For ABB-specific controller assessment or component-level evaluation, the ABB robot repair service is available at https://autonews.best/abb-robot-repair. Verification After Service After an approved repair or installation correction, verify that all covers, cable protection, connections, and safety devices are restored according to the applicable instructions. Review active and historical alarms, then perform any permitted functional checks under controlled conditions and in accordance with ABB operating information and site safety procedure. Motion observation, when relevant, must be performed only by suitably competent personnel under controlled conditions. Do not deliberately repeat a risky action simply to reproduce the original fault. Record the result, operating condition, and any new alarms for future maintenance decisions. Repair Inquiry Information ZHB is an independent industrial robot inspection, repair, and maintenance service provider that also supplies parts to overseas customers. For a technically useful repair inquiry, provide the robot model, controller model, complete alarm code, alarm history, component label, fault conditions, and clear photographs of the relevant cabinet, cable, connector, or visible damage. This information helps determine whether the concern should be assessed as an installation, cable, controller, drive, motor, or feedback-related issue before repair or replacement is considered.

Need a part or repair assessment?

Share the robot model, part number, fault details and destination country with our team.

Contact our team ↗
← All robot insights

Discuss your requirements

Send the model, part number, quantity and destination country, or describe the equipment fault. Our team will review your sourcing or repair requirements.

Contact Us