How to Select ABB Robot Repair Parts? Inspection Guide for Common Control Cabinets, Servo, and Body Spare Parts
When ABB industrial robots experience alarms, inability to enable, operational jitter, or positioning abnormalities, the issue may not only lie with the robot body itself, but could also be related to accessories such as control cabinet drive modules, servo motors, encoders, cables, and braking units. This article introduces the classification of common ABB robot repair parts, key points for model verification, pre-replacement checks, and post-repair validation procedures to help factories reduce secondary downtime caused by incompatible spare parts.

In this article
During long-term operation of ABB robots, the control cabinet, body cables, servo system, and end-of-arm tooling will experience varying degrees of wear or failure. When on-site issues such as servo alarms, teach pendant communication failure, robot inability to enable, abnormal noise from a single axis, or repetitive positioning deviation occur, maintenance personnel often need to make judgments based on alarm codes, fault phenomena, and part status.
Repair parts are not simply "if it fits, it works." Different robot models, controller versions, axis numbers, load configurations, and software parameters all affect part compatibility. Performing model verification and fault confirmation before replacement is essential to avoid repeated downtime.
1. What are the common repair parts for ABB robots?
Common repair parts for ABB robots can typically be categorized into the following groups.
Control Cabinet Parts
Common parts inside the control cabinet include servo drive modules, power supply modules, rectifier units, braking units, main computer units, communication modules, I/O modules, fans, and filters.
When the robot cannot power on, the servo cannot enable, drive alarms occur, communication is interrupted, or the control cabinet temperature is too high, these components should be prioritized for inspection.
Servo and Feedback Parts
Servo system-related parts include servo motors, encoders, feedback cables, power cables, brake connection components, and motor connectors.
Such issues often manifest as a single axis being unable to move, position loss, motion jitter, following error, encoder alarms, or abnormal motor temperature.
Body Mechanical Parts
Common repair parts for the robot body include reducers, bearings, gears, seals, lubrication components, mechanical limit components, and cable packages.
If the robot exhibits abnormal noise, jamming, oil leakage, increased vibration, or abnormal operating current in specific postures, inspection should be combined with the body's mechanical structure.
End-of-Arm and External Parts
External parts typically include welding torches, grippers, jigs, sensors, external axis motors, tool cables, and tooling connection components.
External device interference, changes in tooling weight, cable pulling, or tool collisions may also indirectly trigger ABB robot servo alarms.
2. Before replacing a part, first confirm if the fault truly points to that component.
Directly replacing the drive, motor, or encoder upon seeing an alarm can easily lead to cost waste and may mask the real fault.
The following information should be recorded first:
Robot model and body serial number.
Controller model and software version.
Alarm code, alarm text, and occurrence time.
Axis number where the alarm occurred.
Program and action the robot was executing before the alarm.
Whether the fault occurs continuously or intermittently.
Whether it is triggered under specific positions, speeds, or loads.
On-site photos, control cabinet indicator status, and alarm log screenshots.
For example, an overload alarm on a single axis does not necessarily mean the servo motor is damaged. Increased reducer resistance, bearing wear, tooling collision, incorrect load parameters, or external cable interference can all cause similar alarms.
3. Key verification points for control cabinet parts
Before replacing modules inside the ABB robot control cabinet, verify the original component's nameplate information.
Focus on confirming:
Part order number or part number.
Module model and hardware version.
Applicable control cabinet series.
Interface type and terminal configuration.
Axis number corresponding to the drive module.
Whether the part requires parameter restoration, software configuration, or calibration.
Drive modules with the same appearance may have differences in power rating, interface definition, or software version. Do not judge replaceability based solely on identical shape.
For equipment with drive alarms, also check the module's cooling conditions. Control cabinet fan failure, filter blockage, excessively high cabinet temperature, or loose wiring terminals can all cause drive module abnormalities.
4. How to diagnose servo motors, encoders, and cables
Motor Issues
A faulty motor may manifest as abnormal heating, continuous humming, weak operation, brake failure to release, or insulation abnormalities.
Inspection focus:
Compare motor temperatures of each axis under similar loads.
Check motor power lines and terminals for burning, looseness, or damage.
Check winding resistance and insulation resistance according to the corresponding maintenance manual.
Confirm the brake can release normally under command.
Check for oil contamination, poor cooling, or mechanical interference near the motor.
Encoder Issues
Encoder and feedback system abnormalities may manifest as robot position loss, zero point abnormality, encoder alarms, servo inability to enable, or sudden stops during operation.
Inspection focus:
Check if the encoder feedback cable is bent, crushed, stretched, or has damaged insulation.
Check connector pins for bending, oxidation, looseness, or liquid ingress.
Confirm the cable is not taut when the robot reaches extreme postures.
Record zero point and calibration data to avoid position deviation after replacement.
Mechanical Load Issues
If a single robot axis operates heavily, jitters, makes abnormal noise, or continuously triggers overload alarms, investigate mechanical resistance and external loads.
Inspection focus:
Whether tools, grippers, and workpieces have collided or interfered.
Whether load parameters match the actual tool weight and center of gravity.
Whether the reducer has oil leakage, abnormal noise, or significant temperature rise.
Whether bearings, connection flanges, and mechanical fasteners are loose.
Whether external cables are tangled, dragging, or restricting robot movement.
5. Common fault phenomena and troubleshooting directions
【Single axis stops, "Overload" alarm appears】
Priority check: Mechanical load, tooling, reducer, bearings.
Possible causes: Tool collision, excessive load, reducer jamming, bearing damage, or external mechanism interference.
Action direction: Check work area and tooling status; after power-off and energy isolation, check for abnormal resistance on that axis; verify robot load data.
【Robot motion jitters, "Following Error" appears】
Priority check: Mechanical load, encoder, mechanical connection points.
Possible causes: Excessive mechanical friction, loose connections, unstable encoder feedback, or abnormal reducer backlash.
Action direction: Check mechanical backlash, fasteners, encoder cables and connectors, and confirm if the alarm consistently occurs on the same axis or at the same position.
【Servo cannot enable, "Encoder Fault" appears】
Priority check: Encoder, feedback cable, connectors.
Possible causes: Feedback cable break, loose connector, dirty pins, abnormal encoder signal, or related module failure.
Action direction: Check cable appearance and connector fixation; perform signal and continuity checks according to the corresponding controller maintenance manual.
【Motor overheats, "Motor Temperature" alarm appears】
Priority check: Motor, power cable, control cabinet cooling, and mechanical load.
Possible causes: Long-term overload, poor cooling, winding insulation aging, abnormal motor bearings, or cooling component failure.
Action direction: Check fans, cooling channels, and control cabinet temperature; check motor temperature rise, winding and insulation status, while also investigating mechanical load.
【Robot intermittently alarms at specific positions】
Priority check: Body cables, connectors, cable packages.
Possible causes: When the robot reaches specific postures, the cable is crushed, stretched, or has intermittent internal contact.
Action direction: Run at low speed and observe cable routing, focusing on inspection of bending, fixation, and crushing points near axes J1 to J6.
6. Post-replacement validation after part replacement cannot be omitted.
After completing part replacement, automatic production should not be resumed directly. It is recommended to perform the following validations sequentially:
Confirm control cabinet wiring, grounding, terminals, and protective covers are restored.
Confirm no persistent faults in the alarm log.
Check robot zero point, calibration data, and load parameters.
Perform single-axis operation at low speed, confirming smooth movement of each axis.
Perform multi-axis coordinated motion and no-load trajectory testing.
Gradually restore to normal speed, observing current, temperature, vibration, and abnormal noise.
Perform process sample testing, confirming positioning accuracy, cycle time, and process quality.
Archive the replaced part model, fault cause, handling process, and validation results.
7. Summary
The selection of ABB robot repair parts should be based on alarm information, on-site phenomena, and step-by-step troubleshooting. Servo alarms may be caused by motors, encoders, drive modules, cables, or mechanical loads. First confirm the fault scope, then verify the part model, and finally complete post-repair validation to improve maintenance efficiency and reduce the risk of repeated downtime.
Maintenance Consultation
For further diagnosis of ABB robot faults, please provide the robot model, controller model, alarm code, faulty axis number, operating state when the alarm occurred, as well as on-site photos or videos to facilitate engineer analysis of specific issues in the control cabinet, servo system, or body mechanical parts.
Maintenance Engineer Contact Hotline +86 18122009539
Need a part or repair assessment?
Share the robot model, part number, fault details and destination country with our team.
Contact our team ↗