ABB Robot Annual Maintenance Checklist: Mechanical Body, IRC5 Control Cabinet, and Accuracy Inspection
After continuous operation of ABB industrial robots, mechanical joints, reducers, servo motors, body cables, encoder batteries, and the IRC5 control cabinet gradually experience issues such as lubrication aging, component loosening, reduced heat dissipation, and changes in positioning accuracy. This article compiles the ABB robot annual maintenance checklist, introducing pre-maintenance backup, mechanical body inspection, lubrication maintenance, electrical testing, safety function verification, and restart validation methods.

In this article
The primary purpose of ABB robot annual maintenance is to identify issues such as abnormal reducer lubrication, joint clearance, cable wear, poor control cabinet heat dissipation, encoder battery voltage drop, and zero-point offset before the equipment experiences a downtime failure.
This article applies to common ABB six-axis industrial robots and IRC5 control systems, such as IRB 2600, IRB 4600, IRB 6640, and IRB 6700. Specific lubrication materials, replacement quantities, and operating postures should be based on the corresponding equipment manual.
1. Record Operating Status Before Maintenance
Before formal shutdown, have the robot run a complete production cycle. Record the sound, vibration, temperature rise, positioning performance, and current alarm information for each axis. Simultaneously observe whether the body is leaking oil, whether the program trajectory is deviating, and whether the control cabinet fans are making abnormal noises. These records can serve as a comparison basis after maintenance.
2. Backup Programs and System Data
Before maintenance, back up RAPID programs, system parameters, tool coordinates, workpiece coordinates, load data, I/O configuration, safety configuration, and calibration records. Backup files should note the robot serial number, controller model, and backup date to avoid mixing data from multiple devices. After backup is complete, also check that the files can be read normally.
3. Mechanical Body Appearance and Installation Check
Clean dust, oil stains, and welding spatter from the robot base, manipulator arm, wrist, and flange surfaces. Check if the body housing is scratched, cracked, or deformed. Confirm that base bolts, tool flange, and piping brackets are not loose. Simultaneously observe whether there is oil leakage at the sealing positions of each joint.
4. Reducer and Joint Inspection for Each Axis
Test the forward, reverse, and reversing movements of each axis separately in low-speed manual mode. Check for periodic abnormal noises, stop rebound, noticeable impact, increased vibration, or abnormal temperature rise. If an axis simultaneously exhibits abnormal noise, backlash, and positioning deviation, further inspect the reducer gears, bearings, and lubrication status.
5. Lubricating Oil and Grease Maintenance
Different ABB robots and different axes may use lubricating oil or grease respectively. Before maintenance, it is necessary to confirm the complete robot model, axis number, lubrication material specifications, replacement quantity, and the specified robot posture.
If the drained lubricating oil or grease shows significant darkening, emulsification, odor, metal particles, or other impurities, further inspect the internal wear condition of the reducer. Overfilling may cause increased internal pressure and seal oil leakage, while underfilling can affect gear and bearing lubrication.
6. Servo Motor and Brake Inspection
Check the operating sound, surface temperature, power plug, and feedback plug of each axis servo motor. Confirm that connectors are not loose, oily, contaminated with coolant, or show signs of burning.
Vertical axes should maintain position stably after stopping. If slow sinking, abnormal brake release, or significant changes in brake holding sound occur, focus on inspecting the motor brake and mechanical load.
7. Body Cable and Flexible Harness Inspection
Check if the outer sheath of body cables is cracked, worn through, flattened, or excessively stretched. Pay close attention to the wrist area, near axis two, cable clamps, and connector roots.
For encoder, communication, or servo alarms that only appear in specific robot postures, prioritize checking the flexible cables. Internal conductors in the cable may already be broken but can still conduct temporarily in some postures.
8. Encoder Battery and SMB System Check
Check if the robot has a low battery voltage warning. Confirm the battery casing is not deformed, leaking, or corroded, and that plugs and wiring are not loose, pinched, or have poor contact. Simultaneously verify the battery replacement record, revolution counter status, and axis angles displayed on the teach pendant.
If the revolution counter is already lost, merely replacing the battery will not automatically restore the robot position; it is also necessary to update the revolution counter and verify the robot zero point.
9. IRC5 Control Cabinet Cleaning and Heat Dissipation Check
Clean the exterior, air inlets/outlets, and filter mats of the IRC5 control cabinet. Check if fans have abnormal noises, are stopped, or have reduced speed. Simultaneously observe whether power modules, drive modules, terminals, connectors, and cables are loose, overheated, discolored, or have aged insulation.
For control cabinets in environments with high oil mist, welding fumes, and dust, the inspection cycle for filter mats and fans should be appropriately shortened.
10. Control Cabinet Power and Grounding Check
Check the control cabinet input power, control power, ground wires, and related connection terminals. Confirm there is no looseness or burning.
For equipment that has experienced irregular restarts, communication offline, drive alarms, or teach pendant black screens, focus on checking whether various power supplies are stable during startup and under load. Simultaneously investigate whether external loads have short circuits or overloads.
11. Teach Pendant Inspection
Check if the teach pendant screen has flickering, distorted display, abnormal brightness, or touch drift. Confirm that physical keys, the emergency stop button, and the three-position enabling switch are functioning normally.
Also inspect the teach pendant housing, connecting cable, and control cabinet interface to avoid intermittent black screens and communication interruptions caused by repeated cable bending or loose connectors.
12. End-of-Arm Tooling and Peripheral Equipment Check
Check if the tool flange, fixture, welding torch, gripper, air hoses, vacuum tubes, and sensors are loose, deformed, or worn. Confirm that tool cables do not restrict robot movement.
After tooling is modified or accessories are added, the tool weight, center of gravity, and inertia parameters should be re-verified. Incorrect load data may cause robot vibration, increased servo load, or abnormal collision monitoring.
13. Zero Point and Positioning Accuracy Check
After completing mechanical and electrical maintenance, check the mechanical markings of each axis, revolution counter status, fixed TCP calibration points, tool coordinates, and workpiece coordinates. The robot's position should be consistent when repeatedly reaching the same reference point.
If all program points simultaneously show deviations in a similar direction, first check the robot zero point, tool coordinates, workpiece coordinates, and base position. Do not immediately modify the production program point by point.
14. Safety Function Check
Test the control cabinet emergency stop, teach pendant emergency stop, external emergency stop, safety gate, door lock switch, three-position enabling switch, and safety PLC or safety relay separately.
Test content should include signal triggering, robot stopping, alarm display, reset, and restart processes. Do not only observe whether the safety signal indicator lights change.
15. Restart and Run Verification
During restart, first confirm no tools are left inside the robot and control cabinet, then power on to check system alarms, revolution counters, and current position. Subsequently, perform low-speed forward and reverse movements for each axis, then run the complete program unloaded, focusing on observing the robot's trajectory near fixtures, workpieces, and peripheral equipment.
After confirming normal low-speed operation, gradually increase speed. Finally, perform loaded production and process sample verification.
16. Establish Annual Maintenance Records
After each maintenance, record the robot body model, controller model, cumulative operating time, maintenance items, replaced parts, lubrication materials, inspection results for each axis, and restart verification results.
Simultaneously save system backups, battery replacement records, zero-point check results, and photos of abnormal components to provide a basis for future maintenance and fault diagnosis.
17. Summary
ABB robot annual maintenance should cover the mechanical body, reducer lubrication, servo motors, brakes, body cables, SMB battery, IRC5 control cabinet, teach pendant, and safety system.
After maintenance is completed, it is also necessary to verify the revolution counter, robot zero point, TCP, program trajectory, and loaded operating status. Confirm that mechanical, electrical, accuracy, and safety functions are all normal before resuming automatic production.
Maintenance Consultation
To schedule ABB robot annual maintenance, please provide the robot body model, IRC5 controller model, cumulative operating time, application process, existing alarm information, and on-site equipment photos.
Industrial Robot Repair Hotline: +86 18122009539
Contact Repair Engineer: +86 18122009539
Need a part or repair assessment?
Share the robot model, part number, fault details and destination country with our team.
Contact our team ↗