How to Perform Annual Maintenance on the ABB IRB 4600 Robot? Checklist for Manipulator, IRC5 Controller Cabinet, and Lubrication
After long-term operation of the ABB IRB 4600 robot, wear, aging, and abnormal heat dissipation may occur in the manipulator joints, reducers, servo motors, brakes, manipulator cables, and the IRC5 controller cabinet. This article introduces the preparation work for IRB 4600 annual maintenance, mechanical manipulator inspection, lubrication maintenance, electrical testing, zero point verification, and restart procedures.

In this article
How to Perform Annual Maintenance on the ABB IRB 4600 Robot? Checklist for the Manipulator, IRC5 Controller, and Lubrication Inspection
The ABB IRB 4600 is a six-axis industrial robot commonly used for welding, material handling, machine tending, and material processing. After long-term continuous operation, the lubrication condition of the reducers, manipulator cables, servo motors, brakes, and the cooling system of the controller cabinet will gradually change.
Annual maintenance should not only involve surface cleaning and replacing filter pads but should also establish inspection items based on the robot's cumulative operating hours, load, alarm history, environmental conditions, and process status.
On-site Assessment Conclusion:
The robot maintenance cycle should not be determined solely based on the calendar year. For IRB 4600 robots operating under high load, high temperature, dust, welding fumes, or continuous operation, the inspection cycle should be appropriately shortened according to operating hours and on-site conditions. Lubricant materials, refill quantities, and replacement intervals must strictly follow the ABB manual corresponding to the specific robot model and serial number.
Scope of Application
This article primarily applies to ABB IRB 4600 series robots configured with the IRC5 control system. Maintenance items may vary for different loads, arm reaches, and hardware versions. Specific cycles should be based on the equipment manual and the enterprise's maintenance plan.
- Why Perform Annual Maintenance?
During production, robots are continuously subjected to the following influences:
- Repeated joint acceleration and deceleration.
- Reducers bearing the load of tools and workpieces over time.
- Repeated bending of manipulator cables.
- Frequent operation of servo motors and brakes.
- Dust accumulation and temperature changes inside the control cabinet.
- Contamination from welding fumes, oil mist, or metal dust.
- Impacts from robot collisions and emergency stops.
Regular maintenance can help detect oil leaks, cable wear, fan abnormalities, mechanical looseness, and positioning deviations in advance, reducing the risk of unplanned downtime.
- How to Determine the Robot Maintenance Cycle
The maintenance cycle should comprehensively consider:
- Cumulative robot operating hours.
- Daily startup time.
- Tool and workpiece load.
- Robot motion speed and acceleration.
- Ambient temperature and humidity.
- Levels of dust, oil mist, and welding fumes.
- Frequency of robot emergency stops.
- Recent alarm and repair records.
- Whether the equipment has experienced a collision.
- Requirements for positioning accuracy.
It is recommended to divide maintenance into daily inspections, monthly checks, quarterly inspections, and annual maintenance. Specific lubrication and component replacement cycles should follow the ABB manual.
- What to Prepare Before Annual Maintenance
Before starting maintenance, prepare the following:
- Complete robot model and serial number.
- IRC5 controller model.
- RobotWare software version.
- Corresponding ABB maintenance manual.
- Previous maintenance records.
- Cumulative robot operating time.
- Historical alarm records.
- Lubricants and spare parts of the correct specifications.
- Torque tools, measuring instruments, and cleaning supplies.
- Backups of programs, system, and calibration data.
Also, schedule downtime based on the on-site production plan and confirm the energy isolation scope for the robot, external axes, tools, and peripheral equipment.
- What Data to Backup Before Maintenance
It is recommended to backup:
- Robot programs.
- System parameters.
- Tool data.
- Workpiece coordinates.
- Load data.
- Revolution counter information.
- Calibration data.
- I/O configuration.
- Communication configuration.
- External axis parameters.
After backup, verify that the files can be read normally and name them using the equipment number and date to avoid confusion with backup files from multiple robots.
- Robot Appearance and Structure Inspection
First, conduct an overall inspection of the IRB 4600 manipulator:
- Check if the manipulator housing is cracked or deformed.
- Check for oil leaks and stains on the surface.
- Verify the integrity of joint protective covers.
- Check for loose bolts on the robot base.
- Check for loose bolts on the tool flange.
- Ensure nameplates and warning labels are legible.
- Check for signs of collision on the robot.
- Check if external piping is rubbing against the manipulator.
- Check for interferences within the operating range of each axis.
If oil stains are found, clean the surface first, then operate at low speed to observe the actual leak location.
- Reducer and Joint Inspection
The condition of the reducers directly affects robot positioning and operational stability.
Inspection items include:
- Check for periodic abnormal noises in each axis.
- Check if running resistance differs between forward and reverse directions.
- Check for impact and rebound during direction changes.
- Check for abnormal play in the joints.
- Check for abnormal temperature rise on the reducer housing.
- Check for oil seepage at seal locations.
- Check for vibration when stopped at a position.
- Check for deviations when repeatedly running to the same point.
Observe using low speed, different directions, and different postures. If abnormal noise is concentrated at a fixed mechanical angle, further inspect the reducer, bearings, and lubrication condition.
- Lubricating Oil and Grease Inspection
Different axes and versions of the IRB 4600 may use different lubricants.
Before performing lubrication maintenance, you must confirm:
- Complete robot model.
- Manipulator serial number.
- Corresponding axis number.
- Lubricant name and specification.
- Specified replacement interval.
- Refill and drain quantities.
- Locations of fill and drain ports.
- Required maintenance posture for the robot.
- Whether running for venting or lubricant distribution is needed.
Do not mix different lubricants, and do not determine refill quantities based solely on experience with other ABB robots. Overfilling may cause internal pressure and sealing issues, while underfilling will increase gear and bearing wear.
- Servo Motor Inspection
Key points for servo motor inspection include:
- Check if the motor housing is abnormally hot.
- Check for humming or bearing noise during operation.
- Check if power cable connectors are loose.
- Check the integrity of encoder connectors.
- Check for liquid ingress or burn marks on connectors.
- Check if the motor mounting bolts are loose.
- Check for oil leakage contamination near the motor.
- Check for significant differences in temperature rise among axes under similar operating conditions.
If a single motor temperature is significantly higher than other axes, simultaneously check mechanical resistance, brake, load, and drive output.
9. Brake Function Check
The motor brake is responsible for maintaining the axis position when the robot stops or servo power is disconnected.
Brake abnormalities may manifest as:
- The arm slowly sinks after servo power is turned off.
- Resistance or humming occurs when starting the axis.
- Rebound occurs when the robot stops.
- Motor temperature increases.
- Overcurrent alarms occur during enabling or motion.
When checking the brake, use appropriate supports and testing procedures, especially for joints bearing significant loads like axis 2 and axis 3. Do not rely solely on the brake to support the arm during disassembly and assembly work.
10. Manipulator Cable Check
Manipulator cables move with the joints over time and are prone to internal damage at fixed bending points.
Inspection items include:
- Whether the cable jacket is worn, cracked, or crushed.
- Whether cable clamps are loose or missing.
- Whether the cable rubs against the manipulator housing.
- Whether connectors are loose.
- Whether pins are bent, oxidized, or retracted.
- Whether the cable is subjected to excessive tension.
- Whether the cable becomes taut when the robot reaches extreme postures.
- Whether there are alarms specific to certain postures.
If communication, encoder, or I/O alarms occur when moving to a specific position, focus on inspecting the active cables in that posture.
11. Encoder Battery and Revolution Counter Check
The status of the encoder backup battery affects the robot's absolute position data after power loss.
Key inspection points include:
- Whether there is a low battery voltage alarm.
- Whether the battery replacement record is complete.
- Whether the battery model is correct.
- Whether the plug and wiring are intact.
- Whether the battery compartment is corroded or has liquid ingress.
- Whether the revolution counter status is normal.
- Whether the mechanical markings on each axis correspond with the position data.
Battery replacement status and steps should be performed according to the corresponding equipment manual to avoid loss of the revolution counter due to backup power interruption.
12. IRC5 Controller Cleaning and Cooling Check
Dust accumulation and cooling abnormalities inside the controller affect the main computer, drives, and power supply modules.
Inspection items include:
- Whether the filter mat is clogged.
- Whether the air intake and exhaust vents are clear.
- Whether the fans are rotating normally.
- Whether the fans produce abnormal noise.
- Whether the controller door and seals are intact.
- Whether dust has accumulated on module surfaces.
- Whether there is oil contamination or moisture inside the cabinet.
- Whether modules show discoloration or a burnt smell.
- Whether the grounding connection is reliable.
Do not leave the controller door open for extended periods for cooling, as this disrupts internal airflow and increases the risk of dust and metal debris ingress.
13. Controller Electrical Connection Check
After powering off and completing the specified discharge waiting period, you can check:
- Whether power terminals are loose or show signs of overheating.
- Whether drive module connectors are secure.
- Whether the control power plug is normal.
- Whether communication cables are loose.
- Whether I/O terminals are oxidized.
- Whether cable shielding and grounding are reliable.
- Whether connectors show signs of arcing/burning.
- Whether foreign objects remain inside the controller.
When tightening terminals, use the method specified in the corresponding technical documentation to avoid damaging terminals or circuit boards due to overtightening.
14. Teach Pendant Check
The teach pendant is a high-frequency use component. During annual maintenance, check:
- Whether the screen has discoloration, dark areas, or bright lines.
- Whether the touch screen is accurate.
- Whether physical buttons function normally.
- Whether the emergency stop button can trigger and reset.
- Whether all positions of the enabling device function normally.
- Whether the teach pendant cable is damaged.
- Whether the connector locking mechanism is intact.
- Whether power loss or communication abnormalities occur when moving the cable.
The emergency stop button and enabling device are safety functions; do not only check the normal operation interface.
15. Tool and External Piping Check
Tools and external piping directly affect robot load and motion state.
Inspection items include:
- Tool flange and mounting bolts.
- Welding torch, gripper, or suction cup structure.
- Tool cables and air hoses.
- Water pipes and welding cables.
- External piping attachment points.
- Tool weight and center of gravity.
- Whether the load data matches the actual situation.
- Whether the tool TCP has changed.
After replacing tools, grippers, or piping, reconfirm the load and TCP; do not only adjust program points.
16. Safety System Check
Annual maintenance should verify:
- Controller emergency stop button.
- Teach pendant emergency stop button.
- Safety door switch.
- Safety light curtains or scanning devices.
- Mode selection function.
- Manual mode speed limits.
- Enabling device.
- External interlock signals.
- Peripheral equipment emergency stops.
- Safety circuit alarm history.
Safety function tests should record the test item, actual response, and result; do not only confirm the system has no alarms.
17. Zero Point and Positioning Accuracy Check
After completing mechanical inspection and lubrication maintenance, confirm:
- The status of each axis revolution counter.
- Whether mechanical markings correspond.
- Whether known reference points can be accurately reached.
- Whether the tool TCP has shifted.
- Whether the workpiece coordinate system is correct.
- Whether repeat positioning is stable.
- Whether program trajectories show overall deviation.
If many program points are simultaneously offset, first check the zero point, TCP, and workpiece coordinates; do not modify program points individually.
18. Suggested Tiered Maintenance Plan
Daily or per shift:
- Review current alarms.
- Observe for oil leaks, abnormal noises, and cable condition.
- Check the safety area and tool status.
Monthly:
- Check the controller filter mat and fans.
- Check connectors, external piping, and mechanical fasteners.
- Review historical alarms and abnormal temperature rises.
Quarterly or semi-annually:
- Inspect motors, reducers, brakes, and cables.
- Verify TCP, reference points, and safety functions.
Annual maintenance:
- Perform comprehensive mechanical, electrical, lubrication, calibration, and operational verification.
Actual intervals should be adjusted based on operating hours, on-site environment, and the ABB manual.
19. Post-maintenance restart verification
After completing maintenance, the following should be performed in sequence:
- Confirm no tools are left inside the robot and control cabinet.
- Restore protective covers, connectors, and control cabinet doors.
- Check all safety devices.
- Confirm programs, parameters, and calibration data.
- Run each axis separately at low speed.
- Check forward/reverse and reversing status.
- Observe sound, vibration, and temperature rise.
- Execute a no-load multi-axis coordinated program.
- Restore the tool and perform low-speed load testing.
- Gradually return to normal operating speed.
- Verify positioning and production quality using process samples.
- Record the maintenance items performed and any issues found.
20. Common Questions
Is annual maintenance sufficient for the robot?
Not necessarily. For robots in continuous operation, under high load, or in harsh environments, inspection intervals need to be shortened based on operating time and equipment condition.
Is the reducer lubricating oil the same for all?
No. Different robots, different axes, and different versions may use different lubricants. This must be confirmed according to the corresponding manual.
What to do if program points shift after maintenance?
Check the revolution counter, mechanical zero position, TCP, and workpiece coordinates. Do not directly modify a large number of program points.
Is it okay to just clean a dirty filter cotton?
Decide whether to clean or replace based on the condition of the filter material and equipment requirements, while also checking the fan and internal air ducts.
21. Summary
ABB IRB 4600 annual maintenance should cover the mechanical unit, reducers, lubrication system, servo motors, brakes, unit cables, IRC5 control cabinet, teach pendant, and safety system.
Maintenance intervals should be established considering cumulative operating time, tool load, working environment, and alarm history. After completing maintenance, low-speed single-axis, no-load coordinated, load operation, and process sample verification must also be performed.
Technical content reference: ABB IRB 4600, IRC5 control system maintenance materials, and industrial robot on-site maintenance experience.
Repair Consultation
If ABB IRB 4600 annual maintenance, reducer lubrication, control cabinet maintenance, or positioning accuracy inspection is required, please provide the robot's complete model, unit serial number, IRC5 version, cumulative operating time, and recent alarm records.
Industrial Robot Repair Hotline: +86 18122009539
Contact Repair Engineer: +86 18122009539
Need a part or repair assessment?
Share the robot model, part number, fault details and destination country with our team.
Contact our team ↗