ZhonghengbiaoZHB
Robot parts and independent repair support. From Foshan, China, to your next inquiry. Talk to us ›
ABB Robot Maintenance

What to Check After an ABB Robot Collision? Guide to Mechanical Body, Zero Point, and Positioning Accuracy Inspection

After an ABB robot experiences tool collision, workpiece impact, or mechanical interference, issues such as zero point offset, reducer damage, body cable compression, and decreased positioning accuracy may occur even if it can continue to operate. This article introduces the on-site handling, mechanical inspection, zero point confirmation, and restart verification process after a robot collision.

What to Check After an ABB Robot Collision? Guide to Mechanical Body, Zero Point, and Positioning Accuracy Inspection
In this article

What to Check After an ABB Robot Collision? Guide to Mechanical Body, Zero Point, and Positioning Accuracy Inspection
ABB robots may collide during welding, handling, palletizing, and machine tool loading/unloading due to program point errors, workpiece position changes, fixture abnormalities, or external equipment desynchronization.
After some collisions, the robot may still start and run normally, but this does not mean the equipment is undamaged. Minor collisions can also cause tool position changes, mechanical connection loosening, or body cable compression; severe collisions may damage reducers, bearings, servo motors, and end flanges.
After a collision, first preserve the on-site status, then inspect in the order of mechanical body, tool, cables, zero point, and running accuracy.
1. Common Manifestations After a Robot Collision
After a collision, the robot may exhibit the following phenomena:
The robot stops immediately and generates a collision or servo alarm.
Point positions deviate after the program is rerun.
The end tool cannot accurately reach its original position.
Abnormal noise occurs during low-speed operation of a specific axis.
The robot shakes during startup or stopping.
Motor current or axis temperature abnormally increases.
Tool flange, fixture, or welding torch becomes loose.
Body cables and tool cables are compressed.
The robot can run unloaded but alarms when loaded.
The robot stops again when running near the collision position.
Even if there are no obvious alarms on site, as long as a mechanical impact has occurred, the tool, connectors, and positioning accuracy should be checked.
2. Do Not Immediately Reset and Run After a Collision
After the robot stops, it is not recommended to immediately reset the alarm and resume automatic production. First, confirm the status of personnel and equipment, and record:
The time of the collision.
The program the robot was running.
The point or action where the collision occurred.
The robot posture corresponding to the collision.
The operating speed and load at the time.
The positions of the tool, workpiece, and fixture.
The alarm code displayed on the controller.
The location and direction of the impact.
Whether the program or parameters were modified before the collision.
It is recommended to take on-site photos and videos; do not move the workpiece, fixture, or tool before recording is complete. The on-site status is an important basis for determining the cause of the collision.
3. First Check the End Tool and Fixture
The robot end tool is usually the first part to be impacted; check:
Whether the tool flange bolts are loose.
Whether the welding torch, fixture, or suction cup is deformed.
Whether the tool installation position has shifted.
Whether tool cables, air hoses, and water pipes are damaged.
Whether the workpiece is installed backwards or not positioned correctly.
Whether the fixture opens and closes normally.
Whether the tool weight or structure has changed recently.
If only the tool position has changed, the robot body may not have obvious damage, but the original tool coordinates are no longer accurate. Continuing to run at this point may cause all subsequent points to deviate.
4. Check the Robot Mechanical Body
Collision impact may be transmitted to robot joints, reducers, and bearings. During inspection, focus on:
Whether the robot base bolts are loose.
Whether the housing of each axis is cracked or deformed.
Whether oil leakage appears near the joints.
Whether the reducer produces abnormal sounds.
Whether there is play in bearings and mechanical connection points.
Whether the motor or joint temperature is significantly elevated.
Whether the arm and balancing device are abnormal.
In compliance with safety requirements, the robot can be run at low speed, axis by axis, to observe the motion state of each axis.
If a specific axis exhibits abnormal noise, shaking, or increased resistance at a fixed angle, stop the test and further inspect the corresponding reducer, bearing, and motor.
5. Check Body Cables and Tool Cables
During a collision, cables may be pulled, compressed, or momentarily bent. Common hazards include:
Cable outer sheath damage.
Connector loosening.
Pin bending or retraction.
Cable clamp displacement.
Intermittent contact of internal conductors.
Encoder feedback signal abnormality.
Power cable insulation damage.
If the robot only alarms in specific postures, cables should be a key focus. Cables that appear normal externally may also be internally damaged.
Tool-end welding torch cables, sensor wires, and air hoses also need checking to prevent external cables from creating new tension or interference during robot movement.
6. Confirm Whether the Robot Zero Point Has Shifted
Collisions may cause revolution counter abnormalities, mechanical position changes, or zero point offset. Common manifestations include:
Mechanical marks cannot align after the robot returns to the origin.
Original program points deviate as a whole.
Only the positions of some axes change.
The controller indicates revolution counter or calibration abnormality.
The robot position is inconsistent with the actual posture after restarting.
When checking the zero point, compare the mechanical marks of each robot axis with the position data in the controller. Do not merely modify program points to conceal zero point offset.
If zero point data abnormality is confirmed, first identify the cause, then handle it according to the calibration process for the corresponding ABB robot model. Back up the system and original parameters before calibration.
7. Check Tool Coordinates and Workpiece Coordinates
After a collision, if the robot zero point is normal but the end position still deviates, check the tool coordinates and workpiece coordinates.
Tool coordinate abnormalities may be caused by:
Tool flange displacement.
Welding torch or fixture deformation.
TCP position change.
Tool installation direction change.
Tool fixing bolt loosening.
Workpiece coordinate abnormalities may be caused by:
Fixture overall movement.
Positioning pin damage.
Fixture base loosening.
Workpiece placement position change.
External axis position offset.
Tool coordinates and workpiece coordinates should be verified separately to avoid directly modifying program points in batches. Otherwise, the program may become increasingly chaotic and create new collision hazards.
8. Determine Fault Direction Based on Alarms
【Overcurrent or overload alarm after collision】
Priority check: Mechanical jamming, tool interference, reducer, motor, and power cables.
【Encoder alarm after collision】
Priority check: Encoder, feedback cable, connector, and zero point data.
【Following error after collision】
Priority check: Mechanical resistance, reducer backlash, encoder feedback, and load parameters.
【No alarm after collision but point deviation】
Priority check: Tool installation, TCP, workpiece coordinates, zero point, and mechanical connections.
【Robot alarms again when running to a fixed position】
Priority check: Mechanical interference, body cables, tool cables, and mechanical state of the corresponding axis.
Alarm codes may differ between controllers and RobotWare versions; refer to the alarm descriptions and maintenance manuals for the specific equipment.
9. Identify the True Cause of the Robot Collision
After completing equipment inspection, also analyze the cause of the collision to avoid the same problem recurring after restart.
Common causes include:
Incorrect program point settings.
Tool coordinate or workpiece coordinate changes.
Workpiece clamping not in place.
Fixture and robot action timing error.
PLC interlock signal abnormality.
Incorrect vision positioning results.
External axis position desynchronization.
Incorrect tool or product model switching.
Program modifications not verified at low speed.
Robot running speed set too high.
Cables, air hoses, or peripheral equipment entering the operating range.
It is recommended to record the collision cause, fault location, and handling results in the equipment maintenance file.
10. Robot Restart Verification Process
After robot collision inspection and repair are completed, operation should be restored step by step.
Step 1: Static Inspection
Confirm that the tool, fixture, workpiece, connectors, and all fasteners are in normal condition.
Step 2: Safety Function Check
Verify emergency stop buttons, safety doors, and related interlock signals.
Step 3: Zero Point and Coordinate Check
Confirm robot zero point, tool coordinates, workpiece coordinates, and load parameters.
Step 4: Low-Speed Single-Axis Operation
Operate each axis separately to check for abnormal noise, shaking, and abnormal resistance.
Step 5: Low-Speed No-Load Operation
Execute the original program at low speed without carrying a workpiece, focusing on observing the trajectory near the collision position.
Step 6: Loaded Low-Speed Test
Restore normal tool and workpiece, confirm robot trajectory and load status.
Step 7: Gradually Restore Production Speed
Increase running speed in stages, observing current, temperature, vibration, and positioning.
Step 8: Process Sample Verification
Check product position, welding quality, assembly accuracy, or handling effect.
Only after all verifications are normal can automatic production be resumed.
11. Common Handling Mistakes
Immediately resetting the alarm and continuing operation after a collision.
Only checking the tool, not the mechanical body.
Concealing zero point offset by modifying program points.
Adjusting multiple program points in one batch.
Repeating the collision trajectory without checking cables.
Performing calibration without backing up the system.
Directly resuming high-speed loaded production after normal no-load testing.
Not recording the collision cause and repair results.
These practices may cause secondary collisions, positioning deviations, or further expansion of mechanical faults.
12. Summary
After an ABB robot collision, first preserve the on-site status and alarm records, then inspect the end tool, fixture, mechanical body, cables, zero point, and coordinate data.
If abnormal noise, jamming, oil leakage, temperature rise, or fixed position alarms occur, stop operation and check the reducer, bearings, motor, and cables. After handling, perform low-speed single-axis, no-load trajectory, loaded operation, and process sample verification in sequence.
Maintenance Consultation
If inspection or repair of an ABB robot after a collision is needed, please provide the robot model, controller model, alarm code, collision location, running program, and on-site photos or videos, and contact a maintenance engineer for further judgment.
Industrial Robot Repair Hotline: +86 18122009539
Contact Maintenance Engineer: +86 18122009539

Need a part or repair assessment?

Share the robot model, part number, fault details and destination country with our team.

Contact our team ↗
← All robot insights

Discuss your requirements

Send the model, part number, quantity and destination country, or describe the equipment fault. Our team will review your sourcing or repair requirements.

Contact Us