ZhonghengbiaoZHB
Robot parts and independent repair support. From Foshan, China, to your next inquiry. Talk to us ›
ABB Robot Repair

What Maintenance is Required After 10,000 Hours of Industrial Robot Operation? A Guide to Mechanical, Electrical, and Accuracy Inspections

After an industrial robot has accumulated 10,000 hours of operation, the reducer lubrication, joint clearance, servo motors, brakes, body cables, encoder batteries, and control cabinet cooling systems may exhibit varying degrees of aging. This article introduces the 10,000-hour maintenance items, inspection sequence, fault diagnosis, and recommissioning acceptance methods for robots.

What Maintenance is Required After 10,000 Hours of Industrial Robot Operation? A Guide to Mechanical, Electrical, and Accuracy Inspections
In this article

After an industrial robot has accumulated 10,000 hours of operation, mechanical transmission components, servo systems, cables, encoder batteries, and control cabinet cooling components have typically undergone numerous start-stop cycles, direction changes, and high-load operation. At this point, a more comprehensive maintenance than daily checks should be performed to proactively identify issues such as reducer wear, joint clearance, degraded brake performance, and wire aging.

10,000 hours is an important reference for establishing a phased maintenance plan. Maintenance requirements differ based on brand, model, load, and working environment. Actual maintenance items should also be determined by consulting the equipment manual, accumulated operating time, production cycle, and historical fault records.

Verify Accumulated Operating Time

First, check the robot's accumulated operating time, servo on-time, and production cycle count in the controller, and compare them with the equipment maintenance records. A robot may have been installed for many years but have relatively low actual operating time; conversely, some equipment may have been in operation for a short period but quickly reached 10,000 hours due to continuous three-shift production.

In addition to accumulated time, record the robot's application process, average load, operating speed, and working environment. Robots for handling, palletizing, welding, painting, and machine tool loading/unloading experience different loads and types of contamination, so the maintenance focus will also differ.

Record Pre-Maintenance Operating Status

Before shutting down for maintenance, have the robot run a complete production cycle according to its normal program. Observe the sound, vibration, and positioning performance of each axis during acceleration, deceleration, direction changes, and stopping.

Simultaneously record any current alarms, joint temperatures, program cycle time, gripping positions, and tool status. If a specific axis exhibits noticeable abnormal noise during high-speed operation but is normal at low speeds, focus on inspecting that axis's reducer, bearings, load parameters, and mechanical interference.

Backup Programs and System Data

Before starting maintenance, save the robot programs, system parameters, tool coordinates, workpiece coordinates, load data, I/O configuration, communication configuration, safety configuration, and zero-point calibration data.

Backup files should be saved separately according to the equipment number, and it should be verified that the files can be read normally. For multiple robots of the same model, avoid using incorrect system backups or calibration data due to similar file names.

Check Reducer Lubrication Status

The 10,000-hour maintenance requires a key focus on inspecting the lubricating oil or grease in each axis reducer. Check for oil leaks at joint seal locations and whether the discharged lubricant shows discoloration, emulsification, coking, odor, metal powder, or other contaminants.

Before replacement, verify the robot model, axis number, lubricant specification, specified quantity, and operating posture. Different axes may use different types of lubricating oil or grease. Do not use one material for all joints, nor attempt to solve abnormal noise by overfilling.

Check Joint Clearance and Reducer Wear

Test the forward, reverse, and direction-changing movements of each axis at low speed, observing for impacts, rebound, jitter, or position lag. After the robot stops, check for abnormal tool-end wobbling under specified conditions.

If the mechanical backlash of a specific axis has significantly increased, further inspect the reducer, bearings, connecting components, and mounting bolts. For welding and precision assembly robots, even small joint clearance can cause noticeable position deviation at the tool end.

Check Servo Motors and Brakes

Check the operating sound, surface temperature, power connectors, and encoder connectors of each axis servo motor, observing for abnormal heating, burning, looseness, or liquid ingress.

Vertical axes require a key focus on checking brake holding capability. If axis sinking, delayed brake release, abnormal braking sound, or position change upon restart occurs after the robot stops, further inspect the brake, motor, and mechanical load status.

Check Body Cables and Flexible Harnesses

After 10,000 hours of operation, the robot's body cables have undergone extensive repeated bending. Check the wrist area, near the second axis, base outlet, cable clamps, and connector roots for cracking, abrasion, flattening, or excessive stretching.

If the robot only exhibits encoder, servo, communication, or tool signal alarms in specific postures, focus on inspecting the flexible harnesses. Internal wires in the cable may have broken but temporarily regained conductivity after a posture change.

Check Encoder Batteries and Zero-Point Data

Check the replacement time, battery voltage status, connectors, and wiring of the encoder backup batteries, confirming there are no system alarms for low battery voltage, absolute position, or revolution counter abnormalities.

When replacing batteries, follow the power supply requirements for the corresponding equipment to avoid losing absolute position data due to improper operation. If the robot already has zero-point abnormalities, simply replacing the battery will not restore the original position; zero-point or revolution counter calibration must also be performed.

Check Control Cabinet Power and Cooling System

Clean the control cabinet air inlets/outlets, filter mats, fans, and cooling channels. Check for dust, oil mist, welding fumes, or metal particles inside the cabinet.

Simultaneously, check the control power supply, drive modules, contactors, relays, terminals, and ground wires for looseness, discoloration, burning, or abnormal temperature rise. For equipment experiencing occasional restarts, drive disconnections, or communication interruptions during operation, check if the power supply is stable during startup and under load.

Check Teach Pendant and Safety Circuits

Check the teach pendant display screen, touch function, physical buttons, connecting cable, emergency stop button, and three-position enabling switch. If the teach pendant cable has been dragged or bent for a long time, it may cause intermittent black screens, communication interruptions, and safety circuit alarms.

Subsequently, test the control cabinet emergency stop, external emergency stops, safety doors, door lock switches, safety PLCs, and other safety interlocks, confirming that the triggering, stopping, alarming, resetting, and restarting processes are normal.

Check End Effectors and Peripheral Equipment

Check the tool flange, grippers, clamps, welding torches, vacuum systems, air hoses, valve groups, and sensors for looseness, wear, or deformation. Tool cables and air hoses should retain appropriate slack and should not be pulled tight or rub against the robot body during movement.

If the tool has been modified, had attachments added, or had cables replaced, re-verify the tool weight, center of gravity, and inertia parameters. Incorrect load data increases motor and reducer load and may cause robot jitter or collision monitoring abnormalities.

Check External Axes and Positioners

For robots configured with linear tracks, positioners, or other external axes, also check the external axis reducers, gears, bearings, brakes, motors, cables, and home position status.

For coordinated motion systems, verify the synchronization relationship between the robot and external axes. If the external axis zero point, mechanical mounting position, or workpiece coordinates change, welding and machining paths may experience overall offset.

Verify Robot Zero Point and Positioning Accuracy

After completing mechanical and electrical maintenance, check each axis's mechanical markings, robot zero point, revolution counter, or absolute position status. Use a fixed reference point to verify the TCP (Tool Center Point), tool coordinates, and workpiece coordinates.

If program points exhibit a systematic offset, first check the zero point, TCP, workpiece coordinates, and base position; do not directly modify a large number of program points. For robots requiring higher positioning accuracy, also use calibration tools or measuring instruments to check repeatability performance.

Recommissioning Run Sequence

Before recommissioning, confirm no tools are left around the control cabinet and robot. Then power on and check system alarms, current axis positions, and safety status. First, test each axis's forward and reverse movements at low speed, then run the complete production program without load.

After confirming normal low-speed trajectory, gradually increase the speed, focusing on observing the robot's movements near fixtures, workpieces, and peripheral equipment. Finally, conduct a production test with load, checking positioning, cycle time, temperature rise, noise, and process results.

Establish 10,000-Hour Maintenance Record

The maintenance record should include the robot body model, controller model, accumulated operating time, application process, maintenance items, replaced parts, lubricants used, inspection results for each axis, and recommissioning verification conclusion.

For minor issues found such as slight oil leaks, increased temperature rise, mechanical clearance, or cable wear, take photos and establish follow-up observation records. Continuously comparing data from different maintenance cycles allows for earlier judgment of the degradation trends of reducers, motors, brakes, and cables.

Summary

After an industrial robot has operated for 10,000 hours, key inspections should focus on reducer lubrication, joint clearance, servo motors, brakes, body cables, encoder batteries, control cabinet cooling systems, and safety circuits.

After completing maintenance, it is also necessary to verify the robot's zero point, TCP, program trajectory, external axis synchronization, and operation under load. Only when the equipment's mechanical, electrical, safety, and process results are all normal can automatic production be resumed.

Maintenance Inquiry

To schedule 10,000-hour maintenance for an industrial robot, please provide the robot brand, body model, controller model, accumulated operating time, application process, current alarms, and photos of the equipment site.

Industrial Robot Repair Hotline: +86 18122009539

Contact Repair Engineer: +86 18122009539

Need a part or repair assessment?

Share the robot model, part number, fault details and destination country with our team.

Contact our team ↗
← All robot insights

Discuss your requirements

Send the model, part number, quantity and destination country, or describe the equipment fault. Our team will review your sourcing or repair requirements.

Contact Us