FANUC R-30iB Robot SRVO-062 BZAL Alarm Repair: Encoder Battery and Zero Point Recovery Methods
When a FANUC R-30iB robot displays the SRVO-062 BZAL alarm, it typically indicates that the backup battery voltage for the corresponding axis pulse encoder has been lost, and the encoder absolute position data may have become invalid. This article introduces the differences between the BZAL alarm and low-voltage warnings, battery and wiring checks, faulty axis identification, pulse reset, zero point calibration, and the restart verification process.

In this article
FANUC R-30iB Robot SRVO-062 BZAL Alarm Repair: Encoder Battery and Zero Point Recovery Method
FANUC robots use pulse encoders to record the absolute position of each axis motor. After the robot controller cabinet is powered off, the encoder backup battery continues to maintain the position data. When the battery fails, the connector becomes loose, or the battery line is disconnected, the controller may generate an SRVO-062 BZAL alarm.
On-site diagnostic conclusion:
The BZAL alarm usually cannot be resolved by simply replacing the battery. A new battery can restore backup power, but the lost absolute position relationship still requires pulse reset, zero point calibration, and program point verification based on the robot's actual condition.
Scope of application:
This article primarily applies to FANUC six-axis industrial robots equipped with the R-30iB controller. The operation interface may differ for different robot bodies, controller software versions, and external axis configurations. Refer to the corresponding equipment maintenance manual for specific details.
1. What does the SRVO-062 BZAL alarm indicate?
BZAL typically indicates that the controller has detected that the backup voltage for a specific axis's pulse encoder has dropped to a level insufficient to maintain absolute position data.
After the alarm occurs, the following may be observed:
- The robot servo cannot start normally.
- One or more axes display a BZAL alarm.
- The controller prompts the need for zero point calibration.
- The robot's current position does not match the controller data.
- Existing program points show an overall deviation.
- The alarm persists after battery replacement.
- The alarm appears upon the first startup after the controller cabinet has been powered off for an extended period.
First, record the axis number displayed in the alarm to determine if a single axis, multiple robot axes, or an external axis is affected.
2. What is the difference between BZAL and a low voltage warning?
When the encoder battery voltage begins to drop, the system may first issue a battery low voltage warning. At this stage, the absolute position data is usually not yet lost.
During the low voltage warning stage:
Replace the battery promptly according to the equipment manual requirements. For some models, the controller must remain powered on during replacement to prevent a complete interruption of the encoder backup power supply.
During the BZAL alarm stage:
This indicates that the backup power supply has been interrupted or the voltage is too low, and the absolute position data may be invalid. After replacing the battery, it is usually necessary to complete alarm reset and zero point confirmation.
Therefore, promptly addressing battery low voltage warnings during routine maintenance can reduce the likelihood of needing to recalibrate the robot.
3. Do not run the original program immediately after a BZAL alarm appears.
If the robot's zero point has been lost, the axis positions displayed by the controller may not match the actual mechanical position of the robot body. Running the original program directly under these conditions may cause trajectory deviation or collisions.
First, you should:
- Stop automatic operation.
- Save the complete alarm code and axis number.
- Photograph the robot's current posture.
- Check the mechanical marker line positions of each axis.
- Confirm if any encoders, motors, or batteries have been replaced recently.
- Back up the current programs and system data.
- Check if valid zero point and calibration records have been saved.
Before confirming the zero point, do not compensate for position deviation by modifying a large number of program points.
4. Key points for checking the encoder battery
FANUC robot encoder backup batteries may be installed in the robot body base, battery box, or a designated location specified for the corresponding equipment.
Inspection items include:
- Whether the battery specifications match the original configuration.
- Whether the battery is installed in the correct orientation.
- Whether there is corrosion or liquid ingress in the battery box.
- Whether the plug is loose.
- Whether the battery wire is broken, pinched, or has poor contact.
- Whether the connector pins are bent or oxidized.
- Whether the new battery is within its valid period.
- Whether measurement results meet the requirements of the corresponding manual.
Do not temporarily replace with ordinary batteries or batteries of different specifications. Mismatches in voltage, capacity, plug type, or battery chemistry may cause the alarm to reappear.
5. Why does the alarm persist after battery replacement?
A new battery can only restore the encoder backup power supply; it cannot automatically recover lost position data.
Common reasons for the alarm persisting after replacement include:
- The corresponding pulse encoder alarm reset has not been performed.
- The controller needs to be restarted.
- The battery connector still has poor contact.
- The battery line is open-circuited.
- The encoder itself is faulty.
- The feedback cable is abnormal.
- Zero point data has been lost and calibration has not been completed.
The methods for pulse reset and controller restart may vary with software versions. Follow the instructions in the R-30iB corresponding manual. Before resetting, confirm that the new battery and line status are normal; otherwise, the alarm may reappear.
6. How to determine single-axis alarm vs. multi-axis alarm
【Only one axis shows BZAL】
Prioritize checking that axis's encoder, feedback line, and corresponding connector. If multiple axes share the same battery pack, also check the common power supply line.
【All robot axes show BZAL simultaneously】
Prioritize checking the common battery box, battery plug, common lines, and recent battery replacement operations.
【External axis shows BZAL】
Check the external axis motor encoder, battery configuration, external axis feedback line, and corresponding amplifier channel.
【BZAL appears after motor replacement】
Check the status of the new motor's encoder and recalibrate the corresponding axis based on the mechanical installation position.
If multiple axes alarm simultaneously, it is generally advisable to check for common causes first, rather than directly concluding that multiple encoders have failed simultaneously.
7. Methods to determine if the zero point is lost
After addressing the BZAL alarm, confirm whether the robot's zero point is still accurate.
You can check:
- Whether the mechanical zero point marker lines for each axis can be aligned.
- Whether the axis angles displayed on the teach pendant correspond to the mechanical posture.
- Whether there is deviation when the robot returns to a known reference point.
- Whether the original TCP check point is still accurate.
- Whether the positions of fixed fixtures or calibration pins are consistent.
- Whether program points show a systematic offset.
If all program points deviate in the same direction, priority should be given to checking the robot zero point, tool coordinates, and workpiece coordinates, rather than modifying program points one by one.
8. Common Zero Point Recovery Methods for FANUC Robots
Depending on site conditions and repair scope, the following calibration methods may be used:
Original Zero Point Data Recovery
If reliable factory calibration data or maintenance records are saved, recovery and verification can be performed according to the corresponding manual.
Mark Line Calibration
Move each axis to the position aligned with the mechanical mark lines, then perform the specified zero point calibration operation. Its accuracy is affected by mark line observation and mechanical condition; after calibration, TCP and program point positions still need to be verified.
Single-Axis Calibration
When only one axis loses its zero point due to motor, encoder, or maintenance operations, the corresponding axis can be processed after confirming that other axis data is normal.
Zero Position Tool or Instrument Calibration
Use FANUC-specified calibration tools, jigs, or instruments for higher-precision zero point recovery, suitable for production lines with high requirements for positioning accuracy.
Different calibration methods have different prerequisites. Selection should be based on robot model, repair content, and data retained on site.
9. Mechanical Inspection Before Calibration
Zero point deviation is not necessarily caused only by data loss. Before calibration, also check:
- Whether the robot has experienced a collision.
- Whether the motor installation position has changed.
- Whether there is backlash in the reducer and bearings.
- Whether the tool flange is loose.
- Whether the base bolts are loose.
- Whether the fixture and calibration jig have shifted.
- Whether the tool TCP has changed.
If the mechanical body has already shifted, merely rewriting zero point data may not restore the original accuracy.
10. Alarm Repair Procedure
Step 1: Record the SRVO-062 alarm and the corresponding axis number.
Step 2: Stop automatic operation and save the robot's current posture.
Step 3: Back up programs, systems, and existing calibration information.
Step 4: Check the battery, battery box, connectors, and wiring.
Step 5: Install a new battery with the correct specifications.
Step 6: Reset the pulse encoder alarm according to the corresponding version manual.
Step 7: Restart the controller and check the alarm status.
Step 8: Confirm the mechanical mark lines and the actual position of each axis.
Step 9: Complete zero point calibration based on site conditions.
Step 10: Perform TCP, program point position, and process verification.
11. Post-Repair Restart Verification
After completing battery replacement and zero point recovery, verify in sequence:
- Whether the BZAL alarm has disappeared.
- Whether the current axis angles are reasonable.
- Whether the mechanical mark lines of each axis correspond to the position data.
- Whether low-speed single-axis motion of the robot is normal.
- Whether there are any abnormalities during forward and reverse operation.
- Whether known reference points can be accurately reached.
- Whether the tool TCP has shifted.
- Whether the unloaded program trajectory is normal.
- Whether loaded operation is stable.
- Whether the position and quality of process samples are qualified.
When running the original program for the first time, reduce the speed and focus on observing the robot's trajectory near fixtures, workpieces, and peripheral equipment.
12. Common Questions
Can production be resumed directly after replacing the battery?
After a BZAL alarm appears, first confirm the zero point and program point positions. The disappearance of the alarm does not mean the absolute position has been accurately restored.
Can program points be modified one by one to compensate for deviation?
Not recommended. If the problem originates from the zero point, TCP, or workpiece coordinates, modifying program points one by one will mask the root fault.
When should the battery be replaced?
Replace it promptly when a low-voltage warning appears, and include battery inspection in regular maintenance. The specific cycle should be based on the equipment manual and on-site operating conditions.
What is the reason for all axes alarming simultaneously?
Priority should be given to checking the common battery pack, connectors, and power supply lines.
13. Daily Maintenance Recommendations
- Regularly check for low-voltage battery warnings.
- Establish a robot battery replacement record.
- Save zero point, pulse, and calibration data.
- Verify specifications and operating procedures before battery replacement.
- Check the status of backup batteries before long-term shutdown.
- Verify reference points and TCP after each repair.
- Do not wait until the battery completely fails before taking action.
- Do not power off and replace the battery without confirming the requirements.
14. Summary
When a FANUC R-30iB robot displays an SRVO-062 BZAL alarm, first check the encoder battery, connectors, and backup power supply lines, then confirm whether absolute position data is lost based on the alarm axis number.
Replacing the battery only restores power supply; subsequent steps still need to be completed, including alarm reset, zero point confirmation, low-speed operation, and program trajectory verification. Only after the robot position, TCP, and process results are all normal can automatic production be resumed.
Technical content reference: FANUC R-30iB control system structure, corresponding equipment maintenance data, and industrial robot on-site inspection experience
Content update time: September 2026
Repair Consultation
If you need to handle FANUC robot SRVO-062 BZAL alarms, encoder battery, or zero point loss faults, please provide the robot body model, controller model, complete alarm screen, fault axis number, and photos of the robot's current posture.
Industrial Robot Repair Hotline: +86 18122009539
Contact Repair Engineer: +86 18122009539
Need a part or repair assessment?
Share the robot model, part number, fault details and destination country with our team.
Contact our team ↗