
Repair Guide · 2026-09-12
When the FANUC A290-0561-V503 encoder experiences feedback loss, position abnormality, or servo enable failure, it is necessary to simultaneously check the encoder, battery, feedback cable, and mechanical installation.
Read article →
Repair Guide · 2026-09-12
Introduces the inspection methods for the FANUC R-30iA control system A06B-6117-H207 dual-axis servo amplifier when multi-axis alarms, inability to enable, overcurrent, and overheating occur.
Read article →
Repair Guide · 2026-09-12
When a FANUC robot experiences issues such as servo enable failure, single-axis stop, operation jitter, or drive module alarms, troubleshooting should be conducted step-by-step, covering power supply, motor cables, encoder, mechanical load, and the servo amplifier.
Read article →
ABB Robot Repair · 2026-09-10
When a fault occurs in the ABB IRB 5500 painting robot's ACU-01 air control unit 3HNA013719-001, it may cause issues such as inability to establish air pressure, atomizer failure to start, unstable spray pattern, or painting program interruption. This article introduces troubleshooting methods for the air supply, filters, solenoid valves, pressure feedback, control signals, and the ACU-01 unit itself.
Read article →
ABB Robot Repair · 2026-09-10
When the ABB IRC5P painting control cabinet PSIB-02 interface board 3HNA010419-001 fails, it may cause loss of painting process signals, safety interlock anomalies, inability to start peripheral equipment, or robot program interruptions. This article introduces troubleshooting methods for the control power supply, connectors, I/O signals, communication links, and the PSIB-02 board itself.
Read article →
ABB Robot Repair · 2026-09-10
When the ABB painting robot 3HNA011999-001 high-voltage board malfunctions, it may cause electrostatic high voltage failure to establish, immediate tripping after startup, unstable high-voltage output, or decreased paint transfer efficiency. This article introduces troubleshooting methods for safety interlocks, control power supply, high-voltage generation unit, atomizer, grounding, and the high-voltage board itself.
Read article →
ABB Robot Repair · 2026-09-10
When a fault occurs on the KUKA KR C4 Compact control cabinet interface board 00-188-971, it may cause abnormalities in the 27V control power supply, loss of US1/US2 power supply, I/O modules going offline, interruption of peripheral signals, or the robot failing to start normally. This article introduces troubleshooting methods for the interface board's power supply, connectors, external loads, and the board itself.
Read article →
ABB Robot Repair · 2026-09-10
When the Yaskawa YRC1000 robot JZRCR-APP01-1 teach pendant experiences key unresponsiveness, inability to switch modes, no screen display, or communication interruption, the fault may originate from the keypad membrane, mode switch, connection cables, emergency stop circuit, or internal circuit boards. This article introduces judgment methods for different teach pendant fault phenomena, component inspection sequences, and functional verification procedures after repair.
Read article →
ABB Robot Repair · 2026-09-10
When a fault occurs in the KUKA KR C2 robot's CI3 safety board 00-111-230, it may cause the emergency stop state to be unresolvable, safety door signal abnormalities, drive enable failure, or sudden stops during robot operation. This article introduces the functions of the CI3 safety board, 24V power supply, KCP teach pendant, X11 external safety interface, and troubleshooting methods for dual-channel safety circuits.
Read article →
ABB Robot Repair · 2026-09-10
When faults occur in the ABB MU300 servo motors 3HAC040657-001 and 3HAC040657-002, they may cause robot axes to fail to operate, brakes to not release, motor overheating, abnormal vibration, or position feedback alarms. This article introduces troubleshooting methods for motor windings, insulation, brakes, encoders, bearings, and power cables, as well as the zero-point and recommissioning verification process after motor replacement.
Read article →
ABB Robot Repair · 2026-09-10
When a fault occurs in the FANUC robot A05B-2680-C422 emergency stop unit, it may cause the emergency stop state to be unresolvable, the servo cannot start, safety circuit alarms, or the robot to stop suddenly during operation. This article introduces the functions of the emergency stop unit, dual-channel safety signals, 24V power supply, external emergency stop circuits, and troubleshooting methods for module faults.
Read article →
ABB Robot Maintenance · 2026-09-10
After a long-term shutdown, industrial robots may experience issues such as control cabinet moisture, encoder battery failure, revolution counter loss, changes in joint lubrication status, and abnormal safety signals. This article introduces the mechanical, electrical, power supply, zero point, and program inspection methods before restarting a long-term shutdown robot, helping factories reduce power-on alarms and operational collision risks.
Read article →